Bambu Studio
Bambu Studio 1.7.2.51
Officieel releaserecord voor Bambu Studio 1.7.2.51, gepubliceerd op 4 aug 2023.
Officiële bestanden in deze release
Linux · 2 bestanden
- BambuStudio_fedora-v01.07.02.51-20230804223010.AppImageNiet vermeld in bestandsnaam · 94,1 MiB · 172 downloadsOfficiële download ↗
- BambuStudio_ubuntu-v01.07.02.51-20230804223010.AppImageNiet vermeld in bestandsnaam · 96,0 MiB · 258 downloadsOfficiële download ↗
macOS · 1 bestanden
- Bambu_Studio_mac-v01.07.02.51-20230804223010.dmgNiet vermeld in bestandsnaam · 122,0 MiB · 293 downloadsOfficiële download ↗
Windows · 2 bestanden
- Bambu_Studio_win-v01.07.02.51-20230804223010.zipNiet vermeld in bestandsnaam · 216,9 MiB · 384 downloadsOfficiële download ↗
- Bambu_Studio_win_public-v01.07.02.51-20230804223010.exeNiet vermeld in bestandsnaam · 202,7 MiB · 866 downloadsOfficiële download ↗
Pakketwijzigingen sinds de vorige release
Vergeleken met 1.7.1.62 blijven alle ingedeelde pakketaantallen gelijk, met 5 openbare bestanden.
De aantallen zijn afzonderlijke doorsneden van bestandsnamen van de uitgever op platform, processor en formaat. Ze zijn geen garantie voor compatibiliteit of ondersteuning.
Voorbeeld van release-opmerkingen
Een platte-tekstfragment uit de release-opmerkingen van de uitgever. Open de officiële release voor de volledige en actuele tekst.
De opmerkingen van de uitgever staan in de oorspronkelijke brontaal. Dit fragment is niet automatisch vertaald.
This is a hotfix version based on 1.7.1 ↗
Improvements
Improve the slicing speed at 15% stage
Starting from version 1.7.1, the default wall generator has been switched to Arachne with variable line width enabled by default. Arachne, compared to the classic wall generator, is more complex. Many users have reported a significant increase in processing time - up to 15% - when slicing complex models. Therefore, we have prioritized optimizing the slicing speed when both the Arachne and overhang slowdown features are enabled. Below, you can see a 3mf ↗ test and the slicing time comparison:
However, if the model is extremely complex (for instance, when slicing a lithophane.) and continues to be sliced slowly in the hotfix version, we recommend switching to the classic wall generator or disabling the overhang slowdown feature as a workaround. Please refer to the following example below:
Performance issues are not always quick to resolve, but we will continue to optimize, as always. Please don't hesitate to report any issues you encounter. We greatly appreciate all constructive feedback and suggestions from our users!
Support one wall one top surface or topmost surface with Arachne
One wall on the top surface option is important to improve the top surface quality. After switching the default wall generator to Arachne from V1.7.0 public beta, users reported that the top surface is bad, because Arachne couldn't be used with one wall on the top surface together at the same time.
We have tested this option before and found that this was causing the slicing process to be too slow. However, we found a solution and this option is now available in release.
You can now use the Arachne wall generator with “one wall on top surface” option for both “all top surfaces” and “only topmost surface”. The “only topmost surface” option can only make the topmost layer be one wall, but it can slice much faster than “all top surfaces” when model is very complex.
Please check the comparison below for details.
Bug Fix
- Fix some Flow Dynamics Calibration issues caused by the calibration result not correctly synchronized between Bambu Studio and Printer.
- Display a failed result when found an abnormal value in Flow rate calibration.
- Fix the crash issue when saving calibration result by the Chinese name.
- Refine kinds of translation and pictures on Calibration pages.
- Improve lots of third-party profiles, these profiles are from OrcaSlicer, thanks SoftFever for these commits.
- Fix the load/unload button disappear issue when not connected to AMS, github.com/bambulab/BambuStudio/issues/2145 ↗
- Fixed the plugin installation failure issue on Windows.
- Fix a send-to-print failed issue caused by too long a plate name.
- Fix the Plate can not switch issue on some Linux Platform, github.com/bambulab/BambuStudio/issues/2140 ↗